On December 9th, the first US Marines land on the beach.īush assures the American people and troops involved that this is not an open ended commitment the objective is to quickly provide a secure environment so that food can get through to the starving Somalis, and then the operation will be turned over to the UN peacekeeping forces. On December 5, the UN accepts his offer, and Bush orders 25,000 US troops into Somalia. With only weeks left in his term as president, George Bush responds to the UN request, proposing that US combat troops lead an international UN force to secure the environment for relief operations. The UN appeals to its members to provide military forces to assist the humanitarian operation. Relief flights are looted upon landing, food convoys are hijacked and aid workers assaulted. It all comes from comparing needs, features, speed, portability and cost to determine which is the right buy.What was Operation Restore Hope? Deteriorating security prevents the UN mission from delivering food and supplies to the starving Somalis. ![]() The USB560 adds more features (Advanced Event Triggering, HS-RTDX, etc.), and speed to make you more productive. I am not sure what you target processor is, but it should load in under 30 seconds with a high speed USB 2.0 controller. This should have been included with the unit (choice of PCI or CARDBUS) from our reseller if you only had USB 1.1 on your desktop or laptop. The USB 2.0 emulator will give you a 5-7 times improvement running with USB 2.0 controller. We can utilize the bandwidth of the USB in our USB560 design, thus it performs very well on USB 1.1 and 2.0. This old way did not take advantage of the USB interface. On XDS510-class emulators, this is done on the PC (Intel Processor) and all of the JTAG commands (thousands) had to cross the PC to Emulator interface (ISA, PCI, USB, Parallel Port, etc.). XDS560-class emulators contain an on-board processor which does 75% or more of the JTAG processing. The "560" is the latest emulation technology introduced by TI in May 2002. The USB 2.0 and USB560 JTAG Emulators support ALL of the devices that TI supports in Code Composer Studio (C2000, C5000, C6000, ARM and OMAP).įirst the USB560 is a TI XDS560-class emulator and our USB 2.0 is an XDS510-class emulator. Those drivers are designed to only work with that board and that host interface. If they are trying to use the files that are installed for use with the EVM board's JTAG interface, it will not work. The other most common mistake is that customers do not use the TI DVR file (the one that you use for the TI XDS510 ISA card). The main problem we have had with the C5510 device has been that Rev 2.x has an 8-bit BYPASS in the scan chain, so when you setup CCS with the C55x DVR file, you have to also add in an 8-bit BYPASS. ![]() We use the C5510 EVM, C5509 EVM, and C5510 DSK just fine in the lab for testing. So, in summary, we can support all devices below, one way or another, except those marked with (x). We cannot support the MPSD devices C30-32 as well as the older C4x and C5x DSP's. These devices are shown below with the prefix (#). This is something unique to our device and extends capabilities to the C24xx and VC33 devices in Code Composer v4.1x. This is where we use the TI XDS510 DVR files supported in Code Composer 4.1x and Code Composer Studio 1.x and later. We can also support operation in XDS510-class mode. Please note that you need CCS v2.1 or later to use an XDS560-class driver, which is a requirement imposed by TI. ![]() These are listed below with the prefix (*). Our USB560 & LAN560 supports the same targets as TI supports in Code Composer Studio v2.1 and later and uses the TI provided XDS560 DVR files.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |